Our strategy utilizes four supporting strategic drivers: Portfolio Prioritization; Amplify Innovation; Digital for Operational Excellence and Growth; and Leadership, Talent and Culture for the Avient of the Future. The values shown for the modified SARs represent the unvested portion of the following: 20,600 SARs originally granted on February 22, 2024 (row four), 18,800 SARs originally granted on February 17, 2023 (row five), and 16,000 SARs originally granted on February 14, 2022 (row six). The values shown for the modified RSUs impact the following: 6,400 RSUs originally granted on February 22, 2024 (row eight), 5,550 RSUs originally granted on February 17, 2023 (row nine), and 4,550 RSUs originally granted on February 14, 2022 (row ten).

Additional draft may be required for grained/textured surfaces. 4 Nymax Polymer Formulations Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Adjust transfer position to 98% full • Increase cushion Brittleness Wet material • Check moisture. Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel • Decrease injection speed Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase injection speed Insufficient packing • Increase hold pressure and time Processing Guide 5 Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase packing pressure • Increase gate size Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size Melt and/or mold too hot • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink Too little shrink • Decrease cooling time 6 Nymax Polymer Formulations Burning Process related Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Check moisture. Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Process related • Increase pack pressure • Increase pack time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Processing Guide 7 Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease pack and hold pressure • Adjust transfer position • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

In addition, after two years of extensive development and testing, the brand responsible for the world’s strongest fiber™ is again taking performance to new heights, offering brands and media an exclusive preview of its latest breakthrough technology: Dyneema® Woven Composites.

Dyneema®, the world’s strongest fiber™ – With its unique combination of low weight and immense strength, Dyneema® is a critical component in ultra-light outdoor gear, protective apparel, and footwear that takes performance and comfort to new heights.

The company is dedicated to serving customers in diverse industries around the globe, by creating value through collaboration, innovation and an unwavering commitment to excellence. Senior management uses adjusted operating income, adjusted EPS, and working capital to assess performance and allocate resources because senior management believes that these measures are useful in understanding current profitability levels and that current levels may serve as a base for future performance.

Cut vent depths to 0.0007″–0.0015″ Draft Angle Maintain a minimum draft angle of 1° per side 4 Artisan Pre-Colored Thermoplastics Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Check thermocouples and heater bands Shot size • Increase shot size • Adjust transfer position to 98% full • Increase cushion Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Brittleness Degraded/overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel Gate location and/or size • Relocate gate to non-stress area • Increase gate size to allow higher flow rate and lower molded-in stress Wet material • Check moisture. Sink Marks Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase shot size • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time Too little shrink • Decrease cooling time Burning • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Warp • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Processing Guide 7 Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

At lower rib heights the maximum amount of displacement is much greater than those at higher rib heights. These regions are excellent for ejector pins due to the increased surface area. Ejector Housing The ejector housing height is equal to part height.

see Attachment 1), representing an 11.1x multiple of last twelve months adjusted EBITDA, or 7.6x including anticipated synergies. to adjusted EPS, excluding the impact of step-up depreciation and amortization related to purchase accounting. Less: Lease adjustment

You can minimize the variation by monitoring and adjusting the ink, parameters and garments. Discharge inks will require adjustment if multiple dye lots are used and the overall discharge may appear different.

Bob has been by my side during our transformation and is unquestionably the right leader to take PolyOne to even greater heights in the future. The company is dedicated to serving customers in diverse industries around the globe, by creating value through collaboration, innovation and an unwavering commitment to excellence.