Yes. 6. In the Color business, blind random sampling of the incomming material is used to verify COA data. A system to respond faster is a current goal. 6.

Injection Molding Parameters Base Resin PPA PPS PA 6/6 PA 12 Barrel Temperatures °F (°C)* Rear Zone 550–580 (288–305) 550–580 (288–305) 440–490 (227–254) 440–480 (227–250) Center Zone 560–600 (293–316) 560–615 (293–324) 470–510 (243–266) 460–510 (238–266) Front Zone 580–620 (304–327) 590–630 (310–333) 490–540 (254–282) 480–520 (250–271) Nozzle 575–615 (302 –324) 600–625 (316–330) 520–570 (271–300) 500–530 (260–277) Melt Temperature °F (°C) 575–615 (302–324) 600–625 (316–330) 520–570 (271–300) 500–530 (260–277) Mold Temperature °F (°C) 250–300 (121–150) 250–300 (121–150) 150–200 (66–93) 150–200 (66–93) Pack and Hold Pressure 50–80% of Injection Pressure Injection Velocity 1.0–3.0 in/sec Back Pressure 25–100 psi Screw Speed 25–75 rpm Drying Parameters °F (°C) 6 hours @ 175 (80) 6 hours @ 300 (150) 3 hours @ 180 (82) 3 hours @ 180 (82) Cushion 0.125–0.250 in Screw Compression Ratio 2.5:1–3.5:1 2.0:1–2.5:1 2.5:1–3.5:1 2.5:1–3.5:1 Nozzle Type General Purpose General Purpose Reverse Taper Reverse Taper Clamp Pressure 4–5 tons/in2 of projected area of cavities and runner system * Barrel temperatures should be elevated for compounds designed for electrical insulative properties. Place vents at each 90° intersection and vent to atmosphere. 6. Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time Processing Guide 5 Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase pack pressure/time Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size Melt and/or mold too hot • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease injection speed • Decrease screw rpm • Increase venting Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase injection speed • Increase screw rpm • Decrease cooling time 6 Therma-Tech Burning Melt and/or mold too cold Mold design • Clean, widen and increase number of vents • Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase vent width and locations Mold design • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure Mold design • Increase draft angle Part is too hot 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

WHITE #66 E-187 - 7 COLOR EXTEND RED PEARL PP FR 8-6 LMS-1000

PRODUCT BULLETIN VERSAFLEX™ GP 2810-40N AM VERSAFLEX™ CE 3120-65* AM ONFLEX™ LO 7120-45 AM Applications Personal care grips Consumer packaging Consumer electronics Charging stations HVAC seals Cup holder mats Color Natural Natural Natural Durometer, Shore A 45 66 45 Specific Gravity (kg/m3) 0.87 1.14 1.13 Tensile Strength (PSI) 650 1200 585 Elongation % 700 600 685 Modulus @ 300% |(PSI) 260 585 300 Injection Moldable Yes Yes Yes OM Substrate PP PC, ABS, PC/ABS, COPE PP TECHNICAL PROPERTIES *UL listing does not apply; testing can be completed if required by the customer Copyright © 2021, Avient Corporation. This literature shall NOT operate as permission, recommendation, or inducement to practice any patented invention without permission of the patent owner. 1.844.4AVIENT www.avient.com Take a closer look at the research and testing behind TPEs with antimicrobial additives in our white paper published in Polymer Engineering & Science.

WHITE (NYLON 6/6) LASER MARK WHITE PP FR 8-6 LMS-1000

REPÚBLICA FEDERATIVA DO BRASIL CADASTRO NACIONAL DA PESSOA JURÍDICA NÚMERO DE INSCRIÇÃO 02.166.983/0001-66 MATRIZ COMPROVANTE DE INSCRIÇÃO E DE SITUAÇÃO CADASTRAL DATA DE ABERTURA 03/10/1997 NOME EMPRESARIAL AVIENT BRASIL LTDA. TÍTULO DO ESTABELECIMENTO (NOME DE FANTASIA) ******** PORTE DEMAIS CÓDIGO E DESCRIÇÃO DA ATIVIDADE ECONÔMICA PRINCIPAL 20.99-1-99 - Fabricação de outros produtos químicos não especificados anteriormente CÓDIGO E DESCRIÇÃO DAS ATIVIDADES ECONÔMICAS SECUNDÁRIAS 46.79-6-01 - Comércio atacadista de tintas, vernizes e similares 46.84-2-99 - Comércio atacadista de outros produtos químicos e petroquímicos não especificados anteriormente 46.63-0-00 - Comércio atacadista de Máquinas e equipamentos para uso industrial; partes e peças 28.66-6-00 - Fabricação de máquinas e equipamentos para a indústria do plástico, peças e acessórios 82.11-3-00 - Serviços combinados de escritório e apoio administrativo 64.63-8-00 - Outras sociedades de participação, exceto holdings 71.20-1-00 - Testes e análises técnicas 22.29-3-02 - Fabricação de artefatos de material plástico para usos industriais CÓDIGO E DESCRIÇÃO DA NATUREZA JURÍDICA 206-2 - Sociedade Empresária Limitada LOGRADOURO AV FRANCISCO NAKASATO NÚMERO 1700 COMPLEMENTO ******** CEP 13.295-000 BAIRRO/DISTRITO SAO ROQUE DA CHAVE MUNICÍPIO ITUPEVA UF SP ENDEREÇO ELETRÔNICO FABIANA.SILVA@POLYONE.COM TELEFONE (11) 4593-9279/ (11) 4593-9252 ENTE FEDERATIVO RESPONSÁVEL (EFR) ***** SITUAÇÃO CADASTRAL ATIVA DATA DA SITUAÇÃO CADASTRAL 08/04/2005 MOTIVO DE SITUAÇÃO CADASTRAL SITUAÇÃO ESPECIAL ******** DATA DA SITUAÇÃO ESPECIAL ******** Aprovado pela Instrução Normativa RFB nº 1.863, de 27 de dezembro de 2018.

Fearon 66 2004 Yes M C Gregory J. 3) The Company acquired the Clariant Color business on July 1, 2020 (the “Acquisition Date”). Clariant Color Integration Objectives.

Coincident with the transformational acquisition of the Clariant Color business in 2020, we branded the collective enterprise Avient—a new name for a new kind of materials company. Guatemala City, Guatemala 66. Alicante, Spain 6.

The new formulations can use varying levels for post-industrial recycled content – from 25% to 100% recycled content for polyamide 66 (PA66) and from 25% to 75% recycled content for thermoplastic polyurethane (TPU). Formulations are available globally in black and natural color and in typical reinforcement percentages of long glass fiber, long carbon fiber, or hybrid combinations.

Homepage // News Center // White is the New White: PolyOne Launches Wilflex™ Universal White Ink for Textile Screen Printing KENNESAW, Ga. – PolyOne today unveiled Wilflex™ EPIC™ Single LC White, a new, white ink that is universally compatible with both polyester and cotton fabrics. EPIC Single LC White inks are commercially available in the U.S. today; the upgraded white inks portfolio will be launched globally later this year.