STAN-TONE MB-107270 GREEN STAN-TONE HC PLUS 107271 GREY HCR PP FR 8-6 LMS-1000

PMS 577C (CAP) V2-HC-8198 NIR GREEN V3 PP FR 8-6 LMS-1000

X HC 122606#SR-09308 White GREEN PP FR 8-6 LMS-1000

CDL GREEN X HC 134121#SR-12588 Blue PP FR 8-6 LMS-1000

X HC 67154#SR00430-0001 Cool Grey 10 GREEN 361C V2 PP FR 8-6 LMS-1000

GREEN JUGS PANTONE 1625C HC-7363 PP FR 8-6 LMS-1000

X HC 170468#SR-11821 Gray SILCOPAS GREEN PP FR 8-6 LMS-1000

TEMPERATURE Material Rear Center Front Nozzle Melt Mold Nylon 6,6 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) Nylon 6,6 30% SS 540–570 530–560 530–560 540–570 540–570 200–300 (90–150) PBT 510–410 (265–280) 490–540 (255–280) 480–530 480–530 480–530 150–250 (65–120) PC 14% NiCF 540–570 540–570 530–560 530–560 530–560 150–250 (65–120) ABS 470–520 460–520 460–520 460–530 (240–275) 460–530 (240–275) 100–200 (40–90) PP 440–480 (225–250) 440–480 (225–250) 430–470 (220–245) 420–460 (215–240) 420–460 (215–240) 125–175 (50–80) DRYING Material Temperature °F (°C) Time Minimum Moisture Maximum Moisture Nylon 6,6 14% NiCF 180 (80) 4–5 hours 0.05% 0.20% Nylon 6,6 30% SS 180 (80) 4–5 hours 0.05% 0.20% PBT 14% NiCF 250 (120) 6-8 hours 0.02% 0.03% PC 14% NiCF 250 (120) 3–4 hours 0.02% 0.02% ABS 14% NiCF 200 (90) 2–4 hours 0.05% 0.10% PP 14% NiCF 180 (80) 2–4 hours 0.20% 0.30% Equipment • Feed throats smaller than 2.5" may cause bridging due to pellet size - Larger feed throats will be more advantageous with long fiber EMI shielding resins • General purpose metering screw is recommended - Mixing/barrier screws are not recommended • L/D ratio - 18:1–20:1 (40% feed, 40% transition, 20% metering) • Low compression ratio - 2:1–3:1 • Deep flights recommended - Metering zone 3.5 mm - Feed zone 7.5 mm • Check ring - Three-piece, free-flowing check ring • General purpose nozzle (large nozzle tips are recommended) - Minimum orifice diameter of 7/32" - Tapered nozzles are not recommended for long fiber EMI shielding resins • Clamp tonnage: - 2.5–5 tons/in2 Gates • Large, free-flow gating recommended - 0.25" x 0.125" land length - 0.5" gate depth Runners • Full round gate design • No sharp corners • Minimum of 0.25" diameter • Hot runners can be used PROCESSING Screw Speed Slower screw speeds are recommended to protect fiber length Back Pressure Lower back pressure is recommended to protect fiber length Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) PROCESS CONSIDERATIONS Recommended – retain fiber length (maximize conductivity) • Low shear process • Low screw speed and screw RPM • Slow Injection speed • Fill to 99–100% on first stage of injection - Reduces potential nesting of fibers at gate location - Improves mechanical performance near gate location - Promotes ideal fiber orientation Resin Rich Surface • Achieved when using a hot mold temperature and longer cure times ≥ Max mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could reduce attenuation performance in an assembly Fiber Rich Surface • Achieved when using a cold mold temperature and shorter cure times ≤ Minimum mold temperature recommendation • Improved surface aesthetic • Reduced surface conductivity • Could improve attenuation performance in an assembly www.avient.com Copyright © 2020, Avient Corporation.

PMS 7407 R HC-7220 PP BROWN LOOP II NYL GREEN JADE

HC M549A CLEAR PG 107939.00 OR PP LM PP FR 8-6 LMS-1000