www.avient.com Copyright © 2020, Avient Corporation.

Maintain a minimum draft angle of 1° per side. 4 Therma-Tech Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures • Increase pack and hold pressure • Increase nozzle tip diameter • Check thermocouples and heater bands Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Increase cushion • Decrease transfer position Brittleness Low melt temperature • Measure melt temperature with pyrometer Degraded/ overheated material • Decrease melt temperature • Decrease back pressure • Use smaller barrel/excessive residence time • Decrease screw rpm Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded in stress Fibers on Surface (Splay) Melt temperature too low • Increase injection speed • Increase screw rpm Insufficient packing • Increase pack and hold pressure, and time Processing Guide 5 Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness • Maintain nominal wall thickness Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase pack pressure/time Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size Melt and/or mold too hot • Decrease screw speed Excessive Shrink Too much orientation • Increase packing time and pressure • Increase hold pressure • Decrease melt temperature • Decrease injection speed • Decrease screw rpm • Increase venting Not Enough Shrink Too little orientation • Decrease packing pressure and time • Decrease hold pressure • Increase injection speed • Increase screw rpm • Decrease cooling time 6 Therma-Tech Burning Melt and/or mold too cold Mold design • Clean, widen and increase number of vents • Increase gate size or number of gates Moisture • Verify material is dried at proper conditions Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Weld Lines Melt front temperatures are too low • Increase pack and hold pressure • Increase vent width and locations Mold design • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Excessive orientation • Decrease injection pressure and injection rate Mold design • Increase number of gates Sticking in Mold Cavities are overpacked • Decrease injection rate and pressure • Decrease pack and hold pressure Mold design • Increase draft angle Part is too hot 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

The reliable low liquid level detection system alerts operators when product is running low; adding additional product does not require stopping the machine, so continuous production is possible without any loss of part color. 1.844.4AVIENT www.avient.com Copyright © 2023, Avient Corporation.

1.844.4AVIENT www.avient.com 版权所有© 2022埃万特公司。

可根据要求提供FDA/EU合规信息 1.844.4AVIENT www.avient.com 版权所有© 2022埃万特公司。

回收应用 APR认证 2021 2021 1.844.4AVIENT www.avient.com 版权所有©2021 埃万特公司。

www.avient.com 版权所有© 2020埃万特公司。

1.844.4AVIENT www.avient.com 版权所有© 2021埃万特公司。

海蓝色 适用于汽车电线的 ONCOLORTM 解决方案 适用于交联材料如 XLPE 的 EVA 色母料，以及适用于 T1、T2 和 T3 耐热等级要求的 PVC 色母料 建议使用量为 1-2%，使用量可能因具体用途、工艺、设备和树脂级别不同而存在差异 海蓝色 蓝色 (浅蓝) 适用于通信电缆和光缆应用的 PVC 和 PBT 色母料 适用于发泡和固体绝缘应用的 PE 色母料 为交联材料如 XLPE 专门设计的 EVA 色母料 所有材料建议使用量为 1-2%，使用量可能因具体用途、工艺、设备和合成树脂级不同而存在差异 适用于通信线缆应用的 ONCOLORTM 解决方案 海蓝色 蓝色 (浅蓝) 海蓝色 海蓝色 适用于室外线缆应用的抗紫外色母料 建议 PE 材料使用量为 2%，PVC 材料使用量为 3%，使用量可能因具体用途、工艺、设 备和树脂级别不同而存在差异 www.avient.com 版权所有© 2020埃万特公司。

主要优势 • 优异的可回收性 • 与rPET相容（适合用于>25% rPET含量） • 非尼龙基 • 即时起效的吸氧反应 • 通过灵活调节添加比(LDR)实现长期保质期 • 即使在较高LDR下，瓶身外观依然出色 • 可轻松与现有单层注塑设备一起使用 • 适用于多层注塑设备 产品公告 1.844.4AVIENT www.avient.com 版权所有©2025埃万特公司。