CESA™ Block Additives Antiblocking PRODUCT SELECTION GUIDE Unmodified film and sheet can adhere, causing problems of separation. CESA Block can be used in thin gauge film applications. 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation. CESA BLOCK – STANDARD OFFERINGS POLYMER FAMILY MATERIAL PRODUCT NAME DOSAGE Polyolefin PEA0820045 CESA Block PEA0820045 1–5% Polypropylene PPA0820056 CESA Block PPA0820056 1–5% Polyamide ABA0820022 CESA Block ABA0820022 2–6% Polyester NBA0820024 CESA Block NBA0820024 1–5% Styrenic SLA0820010 CESA Block SLA0820010 1–5% TPU RUA0820028 CESA Block RUA0820028 1–5% CESA Block additives can be used in combination with other CESA masterbatches, and formulations can be customized for most applications.

Cesa Fiber Additives for Heat Preservation Technical Bulletin_TW2.28-1 Cesa™ 紅外蓄熱纖維添加劑 熱影像圖片 加熱前表面溫度：20.22°C 技術公告 埃萬特推出新一代應用於紡織纖維的紅外蓄熱添加 劑配方，旨在幫助品牌商能夠更加輕鬆地滿足消費 者對冬裝、運動裝和床上用品輕量舒適的要求。 與普通織物相比，在暴露於波長為320至1100nm 的日光下，使用Cesa™紅外蓄熱纖維添加劑的紡織 品能吸收更多熱量，同時能達到更高的克羅值（服 裝隔熱保暖性能）。 測試方法：FTTS-FA-010-2007 4.2 設備：紅外線熱像儀 熱源：500W鹵素燈 熱輻射距離：100 cm 加入Cesa紅外蓄熱纖維添加劑 加熱10分鐘後表面溫度：33.85°C 溫度變化：+13.6°C 測試方法 0.9 9°C 8.9°C 5.6°C 0.625 +12.9% +13.6% +1.7% www.avient.com 標準要求 測試結果 GB/T 30127 遠紅外線性能 GB/T 18319-2019 光蓄熱性能 FTTS-FA-010 紅外線性能及蓄熱升溫 GB/T 11048-2008 Method A 熱舒適性 熱阻性能 單位：CLO 人體生理實驗 遠紅外線發射率 ≥0.88 (5-14um) （測試溫度:34°C） 遠紅外線輻射溫升值 ≥1.4°C 最高允許溫升值 ≥6°C 平均溫升值 ≥4.4°C（20分鐘） 平均發射率 ≥ 0.8 (2-22um) （測試溫度: 25°C) 0.81 規定加熱ΔT ≥ 0.5°C （相對於標準） +5.34°C (ΔT) 裸體：0 內褲：0.04 T恤：0.09 厚毛衣：0.35 冬季大衣：0.7 上述所有資料均為參考值 血流量 血流速 血氧濃度（%SpO2） 請聯絡您的埃萬特業務代表以了解 您所在國家或地區是否有售。

CESA Nox Additives - Product Selection Guide Cesa™ Stat Antistatic Additives Cesa™ Light Additives

VALVE-GATED TOOLS IN INJECTION MOLDING GUIDELINES CESA CLEAN ADDITIVES ™ KEY FEATURES Cesa™ Clean Additives • Cesa Clean is a concentrated purge product, not a purge compound. • It can be processed through manifolds, valve-gated tools and small sub gates. • Cesa Clean is 100% recyclable with polyolefin resins and compounds. GUIDELINES FOR USING CESA CLEAN ADDITIVES • Cesa Clean works best when molded maintaining normal (injection) pressure/shear • For best results, Avient recommends a “Running Color Change” which eliminates breaks in the molding cycle • Since the Cesa Clean concentrate will expand, it is recommended to reduce the shot size by 20% • It is designed for use at a let-down ratio (LDR) of 3.0% or (33:1); however, use rate can vary depending on the severity of the contamination but typically is 2.0–4.0% (a use rate higher than 6.0% may not have any positive affect on the cleaning performance) • Using Cesa Clean as a routine part of your color change rotation will allow faster changes and consume a minimal amount of raw material - Note: If the manifold is not cleaned routinely, this process may be more time consuming and additional material will be required • It is best to process at your normal polymer processing temperatures - For best performance, stock temperature should be at least 400°F - If 400°F is achieved during the purging process, no additional activation will occur during the reprocessing of regrind - All parts produced during the “Running Purge Cycle” should be captured as regrind, resulting in a scrap-free color change - If using sequential gates, open and close all gates at the same time while purging the tool - If contamination appears to be coming from one gate, open and close first, and for an extended period of time, to force more material through this location - When cleaning in this manner, pay close attention to shot size - Parts containing the previous or new color plus any Cesa Clean can be used as regrind INTRODUCING CESA CLEAN TO YOUR PROCESS Hand Blend • Hand weigh enough of the Cesa Clean and natural resin mix to equate to 3–5 times the barrel capacity • Use rate should be 3.0% or 33:1 for routine cleaning • For difficult-to-clean tooling, or tooling which is not routinely cleaned, start at 4.0% or 25:1 • Note: Do not attempt to vacuum load more than 15 feet from source as stratification/separation may occur Volumetric Feeder • Calibrate feeder to dispense 3.0% or 33:1 for routine cleaning • For difficult-to-clean tooling, or tooling which is not routinely cleaned, start at 4.0% or 25:1 • This style of feeder is highly recommended for at-the-throat metering of Cesa Clean Blending Units Most blenders have an extra bin for an additive • Fill the additive bin with Cesa Clean • Set blender to introduce the Cesa Clean at 2.0 to 4.0% • Note: Do not air convey any further than 15 feet as Cesa Clean has a high density and may separate from the mix. GETTING STARTED TIMING IS THE KEY TO A RUNNING COLOR CHANGE Hand Blend • Have the purge blend ready to load • If hopper contains a mixture of resin, color and/ or regrind, it should be run dry or drained before beginning the color change, keeping the screw full so press cycle continues • Run the main resin hopper dry or shut off hopper to hand feed at the throat • Once press is clean, slide hopper in place and proceed with next color-resin blend • The next color can be added while Cesa Clean is still in the barrel • When splay is no longer visible in parts, reset shot size, parts should be ready to pack (Single) Volumetric/Gravimetric Metering Unit at the Throat • Empty and clean feeder while press continues to run • Add Cesa Clean to the feeder color hopper and calibrate to a 3.0% use rate • When press is clean, start next color • When splay is no longer visible in parts, reset shot • Note: If an open/unused secondary feeder is installed, use it for the Cesa Clean concentrate Central Blending Unit • Thoroughly clean unit while continuing to mold parts, keeping a resin feed to the press • Using a clean open hopper or regrind hopper, add the Cesa Clean concentrate • Set blender for additive/color to 3.0% • Once press is clean, drain hopper and/or central blending unit while continuing to mold parts • Begin new color and continue to mold parts • When splay is no longer visible in parts, reset shot Process Adjustments That Can Help • Increase back pressure • Increase screw speed • Increase injection speed (in some tools maximum injection speed can facilitate cleaning) • Reduce mold close time (faster cycle) • Always remember a stock temperature of 400°F is essential When press and tool are clean, return all settings to standard production process profile.

CESA Fiber Additives for Heat Preservation ProductBulletin_CN4.27-2 CESA™ 红外蓄热纤维添加剂 1.844.4AVIENT www.avient.com 版权所有©2021 埃万特公司。 CESA™ 红外蓄热纤维添加剂是一种配方添加剂， 满足GB/T 30127-2013标准，可用于增强合成纤 维纺织品的保暖性能。 相较于常规织物，使用此 CESA纤维添加剂织物在暴露阳光下能够吸收更多 的热量。

MB CLARIANT WHITE VER. 2 UV YELLOW 114C UV ROYAL BLUE 2728C

Cesa™ Clean masterbatch additives are formulated to effectively clean process tooling and machinery during material or color changeovers. Cesa™ Clean Additives WHEN TO USE CESA CLEAN As a best practice, Cesa Clean adds value when used for: • Color changeovers • Material and formulation changes • Shutdown or startup • Machine maintenance WHY USE CESA CLEAN Some of the ways you can benefit from consistently using Cesa Clean: • Improve production uptime with faster color changeovers • Reduce wasted melt puddle material • Reduce resin use during purging • Non-abrasive and safe to use on precision equipment PRODUCT BULLETIN Cesa Clean solutions are available for use in a variety of processing conditions and operating temperatures.

PRODUCT BULLETIN Cesa™ Fiber Tracer Concentrates The textile supply chain is usually long and complex, with several material and service suppliers playing a role. Cesa™ Fiber Tracer Concentrates are polymer solutions that include a taggant, unique to the customer/product line, which is incorporated into the fibers during the spin-dyeing process. Cesa Fiber Tracer Concentrates contain no hazardous raw materials and comply with key fiber regulations.

Colorant Chromatics™ UV Laser Marking Additives delivered a high quality product with no clumping during the extrusion process Cesa™ Light Additives for Injection Molded Applications Cesa™ Anti-Block Slip LS

Colorant Chromatics™ UV Laser Marking Additives delivered a high quality product with no clumping during the extrusion process Cesa™ Light Additives for Injection Molded Applications Cesa™ Anti-Block Slip LS