We recently set a goal to complete 100% of risk assessments on hazardous materials greater than 1 ton by 2025. In 2023, we will be setting a baseline on use of these listed hazardous substances with the intention of setting a target to reduce and ultimately remove these materials from our product portfolio. Our Code of Conduct establishes a clear set of ethical and behavioral standards for our business conduct.

By setting and regularly reviewing our environmental objectives and targets, we strive for excellence in environmental leadership The price was set at 54.58/ MT CO2 in 2022 and by 2023, it increased to 56.76. They then set up 4 bins in production to sort our plastic scrap into bins of PE/PP, PS, Nylon, and High Temp materials.

Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location Warp Process related • Increase pack pressure • Increase pack time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Processing Guide 7 Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease pack and hold pressure • Adjust transfer position • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

Sink Marks Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase shot size • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time Too little shrink • Decrease cooling time Burning • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Warp • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Processing Guide 7 Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

This achieves both the ease of running continuously and reduces lost time associated with set up.

Except to the extent attributable to the Product failing to meet the express warranties set forth in paragraph 1, Buyer will indemnify, defend and hold Seller harmless from all costs, expenses, damages, judgements or other loss, including costs of investigation, litigation and reasonable attorney’s fees, arising out of Buyer’s selection, use, sale and further processing of the Product. 9.

Copolyester, Polyester & PC/Polyester Blends Copolyester Eastman Tritan™ (Copolyester) High chemical resistance to a wide variety of hospital disinfectants; excellent toughness and impact resistance after disinfection; retains color and gloss after sterilization and disinfection; does not contain BPA, BPS or halogens Polybutylene Terephthalate (PBT) DuPont™ Crastin® & Rynite® (FR-PBT) 30% glass reinforced; flame retardant; good mold flow and electrical properties; high strength, stiffness, dimensional stability and heat resistance Polyester (PC/PET) & Polybutylene Terephthalate (PC/PBT) Covestro Makroblend® (FR-PC/PET) & (FR-PC/PBT) Strength; toughness; chemical resistance; flame retardant Covestro Makroblend® (Non-FR PC/PBT) Strength; toughness; chemical resistance; limited biocompatibility Trinseo EMERGE™ (FR-PC/PET) Chemical resistance; ignition resistance; limited biocompatibility PA, PVC, PC & PMMA Polyamide (Nylon, PA) Avient Trilliant™ XR Radiation Shielding (PA) Radiation shielding; green alternative for lead replacement; enhanced design freedom vs. lead; available in hard and soft durometers Arkema Rilsan® MED (PA11) & Rilsamid® MED (PA12) Chemical resistance; transparent and opaque; easy processing; creep resistance; temperature resistance; BPA-free; sterilizable by gamma, EtO and steam Polyvinyl Chloride GEON Performance Solutions Resilience™ HC (PVC) Excellent chemical resistance; good strength and stiffness; very good surface quality; inherently flame resistant; available in all medical colors; excellent solvent bonding to PVC Polycarbonate (PC) Trinseo EMERGE™ (PC) Ignition resistant; transparent and opaque; glass-filled also available PolyMethyl Methacrylate (PMMA) Trinseo Plexiglas® Acrylics (PMMA) Clarity; easy processing; chemical resistance; BPA free; ideal for light piping and lenses Styrenics & FR-PC/ABS Blends Styrenics Trinseo MAGNUM™ (ABS) Opaque; custom colors; excellent impact and flow; low residuals; full biocompatibility INEOS Styrolution Terlux® HD (MABS) Good clarity; good heat and overall chemical resistance; good impact strength; good solvent bonding to PVC; outstanding surface quality INEOS Styrolution Lustran® & Novodur® HD (ABS) Opaque appearance; outstanding chemical resistance; high impact strength; excellent balance of properties; ease of processability; bondable FR- Polycarbonate/ ABS (FR-PC/ABS) Covestro Bayblend® (FR-PC/ABS) Flame retardant; good impact resistance; dimensional stability; toughness Trinseo EMERGE™ (FR-PC/ABS) Ignition resistant; limited biocompatibility; high flow; easy processing; glass-filled also available RIGID COMPONENTS: DIAGNOSTIC, IMAGING, LIFE SUPPORT, LABORATORY, Applications include: • Housings • Covers • Monitor bezels • Body panels • Handles • Access panels • Battery enclosures • Wands • Coils Rigid Component Solution Needs: • Materials compliant with ISO 10993 & USP Class VI, if required • UL approved resins to meet flammability requirements • Housings with toughness & good impact resistance • Enclosures & components that withstand repeated cleanings • High-flow materials for components with complex designs FLEXIBLE COMPONENTS: DIAGNOSTIC, IMAGING, LIFE SUPPORT, LABORATORY, Applications include: • O-rings • Gaskets • Wheels • Soft touch grips/handles • Keypads/displays • Diaphragms • Seals Flexible Component Solution Needs: • Comfortable handles & grips • Water-tight seals • Durable feet or casters • Durable keypads • Flow control TPE, TPC-ET, TPU, TPV & Flexible PVC Thermoplastic Avient Versaflex™ HC Overmolding Series Proven healthcare solutions with hardness ranges 42–65 Shore A; autoclave, radiation and EtO sterilizable; bondable to many substrates; customizable haptics Arkema Pebax® MED Sterilizable by gamma and EtO; low energy return; soft touch; chemical resistance; overmolding material Thermoplastic Polyester DuPont™ Hytrel® Wide range of flexibility, stiffness, and processing options; Shore D between 30-82; BPA-free; excellent flex fatigue and toughness; low temperature flexibility; good chemical resistance Thermoplastic Polyurethane Covestro Texin® Biocompatible; soft touch; sterilizable; good chemical resistance; overmold for grips and handles; excellent bonding to polar substrates like PC; 70A to 95A Thermoplastic Vulcanizate Avient Versalloy™ Proven healthcare solutions with hardness ranges 45–90 Shore A; autoclave, radiation and EtO sterilizable; natural and colorable; smooth texture; bonds to PP Exxon Mobil Santoprene™ Durable sealing performance; elastic recovery; excellent chemical resistance; compliance with medical standards Flexible Polyvinyl Chloride GEON Performance Solutions Geon™ Flexible PVC Engineered exclusively for the healthcare market; transparent and opaque colors; radiopaque grades available; durometer ranges from 55A to 40D; gamma and EtO sterilizable Thermoset Silicone Elastomers Thermoset Silicone Elastomers/ Liquid Silicone Rubber (LSR) DuPont™ Liveo™ Silicone Elastomers (LSR) Biocompatible; non-irritating and non-sensitization; sterilizable; made without plasticizers, phthalates or latex PVC Polyvinyl Chloride GEON Performance Solutions Geon™ Flexible PVC Inherent flame resistance; halogen-free; excellent chemical resistance; non-yellowing; proven safety record in wire and cable applications; high temperature grades available TPE, TPC-ET, TPU & POE Thermoplastic Polyester Arkema Pebax® Flexibility; chemical resistance; easy processing; abrasion resistance; low coefficient of friction Thermoplastic Polyester Elastomers (TPC-ET) DuPont™ Hytrel® REACH, RoHS and WEEE compliant; wide range of flexibility, stiffness, and processing options; 30D-82D; BPA-free; excellent flex fatigue and toughness; low temperature flexibility; good chemical resistance Thermoplastic Polyurethane Covestro Texin® RoHs, WEEE, and REACH compliant; excellent memory and recoil; abrasion resistance; Texin® Rx Series - medical grade Polyether TPU – 70A to 80D Polyolefin Elastomer (POE) Avient ECCOH™ Non-halogenated flame retardant; high flexibility; environmental stress cracking resistance (ESCR); good electrical properties PA Polyamide (Nylon, PA) Arkema Rilsan® (PA) Chemical resistance; easy processing; abrasion resistance; low coefficient of friction; dimensional stability WIRE & CABLE: DIAGNOSTIC, IMAGING, LIFE SUPPORT, LABORATORY, Applications include: • Plug molding • Flexible jacket • Heater cable insulation • Flexible cords • Coil cords & cable Wire & Cable Component Solution Needs: • Materials compliant with UL, RoHS, REACH & WEEE, if needed • Materials with good chemical, moisture & abrasion resistance • Low smoke & non-halogen materials CUSTOM AVIENT SOLUTIONS FOR MEDICAL EQUIPMENT Custom Solution Needs Avient™ Custom Solutions Specialized materials to meet unique application requirements Avient Trilliant™ Healthcare products are a line of customized solutions specific for regulated medical devices; color branding expertise FDA-registered pre-colored resins and masterbatch options; color coding for safety and brand recognition Avient collaborates with key material suppliers to provide FDA-approved pre-colored resins Avient OnColor™ HC Plus offers customizable color masterbatch solutions pre-certified for biocompatibility using ISO 10993 and USP Class VI test protocol Reduced growth of microbes Avient WithStand™ additive technologies inhibit growth of microbes that often cause odor, staining and loss of mechanical properties AVIENT DISTRIBUTION Healthcare Supplier Line Card You face a unique set of challenges when designing parts for the healthcare industry.

RIGID COMPONENTS: DIAGNOSTIC, IMAGING, LIFE SUPPORT, LABORATORY, & MONITORING EQUIPMENT (housings & covers, monitor bezels, body panels, handles, battery enclosures, access panels, wands, coils) Rigid Component Materials compliant with ISO 10993 & USP Class VI, if required UL approved resins to meet flammability requirements Housings with toughness & good impact resistance Enclosures & components that withstand repeated cleanings High-flow materials for components with complex designs Copolyester, Polyester & PC/Polyester Blends Copolyester Eastman Tritan™ (Copolyester) High chemical resistance to a wide variety of hospital disinfectants; excellent toughness and impact resistance after disinfection; retains color and gloss after sterilization and disinfection; does not contain BPA, BPS or halogens Polybutylene Terephthalate (PBT) DuPont™ Crastin® & Rynite® (FR- PBT) 30% glass reinforced; flame retardant; good mold flow and electrical properties; high strength, stiffness, dimensional stability and heat resistance Polyester (PC/PET) & Polybutylene Terephthalate (PC/PBT) Covestro Makroblend® (FR-PC/PET) & (FR-PC/PBT) Strength; toughness; chemical resistance; flame retardant Covestro Makroblend® (Non-FR PC/PBT) Strength; toughness; chemical resistance; limited biocompatibility Trinseo EMERGE™ (FR-PC/PET) Chemical resistance; ignition resistance; limited biocompatibility PA, PVC, PC & PMMA Polyamide (Nylon, PA) Avient Trilliant™ XR Radiation Shielding (PA) Radiation shielding; green alternative for lead replacement; enhanced design freedom vs. lead; available in hard and soft durometers Arkema Rilsan® MED (PA11) & Rilsamid® MED (PA12) Chemical resistance; transparent and opaque; easy processing; creep resistance; temperature resistance; BPA-free; sterilizable by gamma, EtO and steam Polyvinyl Chloride GEON Performance Solutions Resilience™ HC (PVC) Excellent chemical resistance; good strength and stiffness; very good surface quality; inherently flame resistant; available in all medical colors; excellent solvent bonding to PVC Polycarbonate (PC) Trinseo EMERGE™ (PC) Ignition resistant; transparent and opaque; glass-filled also available PolyMethyl Methacrylate (PMMA) Altuglas Plexiglas® Acrylics (PMMA) Clarity; easy processing; chemical resistance; BPA free; ideal for light piping and lenses Styrenics & FR-PC/ABS Blends Styrenics Trinseo MAGNUM™ (ABS) Opaque; custom colors; excellent impact and flow; low residuals; full biocompatibility INEOS Styrolution Terlux® HD (MABS) Good clarity; good heat and overall chemical resistance; good impact strength; good solvent bonding to PVC; outstanding surface quality INEOS Styrolution Lustran® & Novodur® HD (ABS) Opaque appearance; outstanding chemical resistance; high impact strength; excellent balance of properties; ease of processability; bondable FR- Polycarbonate/ ABS Covestro Bayblend® Flame retardant; good impact resistance; dimensional stability; toughness Trinseo EMERGE™ Ignition resistant; limited biocompatibility; high flow; easy processing; glass-filled also available Flexible Component Solution Needs: Comfortable handles & grips Water-tight seals Durable feet or casters Durable keypads Flow control TPE, TPC-ET, TPU, TPV & Flexible PVC Thermoplastic Avient Versaflex™ HC Overmolding Series Proven healthcare solutions with hardness ranges 42–65 Shore A; autoclave, radiation and EtO sterilizable; bondable to many substrates; customizable haptics Arkema Pebax® MED Sterilizable by gamma and EtO; low energy return; soft touch; chemical resistance; overmolding material Thermoplastic Polyester DuPont™ Hytrel® Wide range of flexibility, stiffness, and processing options; Shore D between 30-82; BPA-free; excellent flex fatigue and toughness; low temperature flexibility; good chemical resistance Thermoplastic Polyurethane Covestro Texin® Biocompatible; soft touch; sterilizable; good chemical resistance; overmold for grips and handles; excellent bonding to polar substrates like PC; 70A to 95A Thermoplastic Vulcanizate (TPV) Avient Versalloy™ (TPV) Proven healthcare solutions with hardness ranges 45–90 Shore A; autoclave, radiation and EtO sterilizable; natural and colorable; smooth texture; bonds to PP Exxon Mobil Santoprene™ (TPV) Durable sealing performance; elastic recovery; excellent chemical resistance; compliance with medical standards Flexible Polyvinyl Chloride GEON Performance Solutions Geon™ Flexible PVC Engineered exclusively for the healthcare market; transparent and opaque colors; radiopaque grades available; durometer ranges from 55A to 40D; gamma and EtO sterilizable Thermoset Silicone Elastomers Thermoset Silicone Elastomers/ Liquid Silicone Rubber DuPont™ Liveo™ Silicone Elastomers (LSR) Biocompatible; non-irritating and non-sensitization; sterilizable; made without plasticizers, phthalates or latex FLEXIBLE COMPONENTS: DIAGNOSTIC, IMAGING, LIFE SUPPORT, LABORATORY, MONITORING EQUIPMENT (o-rings, gaskets, wheels, soft touch grips/handles, keypads/displays, diaphragms, seals) WIRE & CABLE: DIAGNOSTIC, IMAGING, LIFE SUPPORT, LABORATORY, & MONITORING EQUIPMENT (plug molding, heater cable insulation, flexible jacket, flexible cords, coil cords & cable) Wire and Cable Component Solution Needs: Materials compliant with UL, RoHS, REACH & WEEE, if needed Materials with good chemical, moisture & abrasion resistance Low smoke & non- halogen materials PVC Polyvinyl Chloride GEON Performance Solutions Geon™ Flexible PVC Inherent flame resistance; halogen-free; excellent chemical resistance; non-yellowing; proven safety record in wire and cable applications; high temperature grades available TPE, TPC-ET, TPU & POE Thermoplastic Polyester Arkema Pebax® Flexibility; chemical resistance; easy processing; abrasion resistance; low coefficient of friction Thermoplastic Polyester Elastomers (TPC-ET) DuPont™ Hytrel® REACH, RoHS and WEEE compliant; wide range of flexibility, stiffness, and processing options; 30D-82D; BPA-free; excellent flex fatigue and toughness; low temperature flexibility; good chemical resistance Thermoplastic Polyurethane Covestro Texin® RoHs, WEEE, and REACH compliant; excellent memory and recoil; abrasion resistance; Texin® Rx Series - medical grade Polyether TPU – 70A to 80D Polyolefin Elastomer (POE) Avient ECCOH™ Non-halogenated flame retardant; high flexibility; environmental stress cracking resistance (ESCR); good electrical properties PA Polyamide (Nylon, PA) Arkema Rilsan® (PA) Chemical resistance; easy processing; abrasion resistance; low coefficient of friction; dimensional stability CUSTOM AVIENT SOLUTIONS FOR MEDICAL EQUIPMENT Custom Solution Needs Avient™ Custom Solutions Specialized materials to meet unique application requirements Avient Trilliant™ Healthcare products are a line of customized solutions specific for regulated medical devices; color branding expertise FDA-registered pre-colored resins and masterbatch options; color coding for safety and brand recognition Avient collaborates with key material suppliers to provide FDA-approved pre-colored resins Avient OnColor™ HC Plus offers customizable color masterbatch solutions pre-certified for biocompatibility using ISO 10993 and USP Class VI test protocol Reduced growth of microbes Avient WithStand™ additive technologies inhibit growth of microbes that often cause odor, staining and loss of mechanical properties AVIENT DISTRIBUTION Healthcare Supplier Line Card You face a unique set of challenges when designing parts for the healthcare industry.

The barrel temperature of the injection molding machine was set from 180°C to 220°C (360°F to 430°F) and the injection velocity from 0.7 inch/sec to 2.0 inch/sec.

Certificate Avient Corporation This is to certify that the Environmental Management System of: Avon Lake Corporate 33587 Walker Road Avon Lake OH 44012 United States (WITH ADDITIONAL FACILITIES LISTED ON ATTACHED ANNEX) has been assessed by ABS Quality Evaluations, Inc. and found to be in conformance with the requirements set forth by: The Environmental Management System is applicable to: Responsible Care Corporate Support Activities in Sr.