• Custom sizes, profiles, tooling design and prototyping available for specific applications USES AND APPLICATIONS Transportation - Automotive chassis, automotive body panels, marine stringer systems, floor strengthening and stability reinforcement Consumer - Watersports paddles, sporting goods sticks, tent poles, fishing rods, archery bow limbs and arrow shafts, bicycle frames, sail battens Infrastructure & Construction - Bridge support and retrofitting repair, support beams, concrete reinforcement Healthcare - Orthopedic external fixators Energy - Wind turbine blades and stiffeners PRODUCT BULLETIN Property CFRP Barstock, Laminates & Pultruded Profiles Resin Epoxy, Vinyl ester Tensile Strength 400–500 ksi 2758–3447 MPa Flexural Strength 130–350 ksi 896–2413 MPa Flexural Modulus 18–22 msi 124–152 GPa Glass Transition Temperature 149–320 °F 65–160 °C Density 0.056–0.060 lb/in3 1.54–1.65 g/cm3 TECHNICAL PROPERTIES (Typical Values) 1.844.4AVIENT www.avient.com Copyright © 2021, Avient Corporation.

DISTINGUISHED CLOSURES FOCUSED ON LUXURY PERCEPTION © 2020, All Rights Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012 THE CHALLENGE Beverage selections can say a lot about who you are and what you aspire to be.

Screw Speed Low–moderate Injection Velocity 1–3 inch per second Back Pressure Low–moderate Pack Pressure 60–80% of max injection pressure Hold Pressure 40–60% of max injection pressure Cool Time 10–30 seconds (depends on part geometry and dimensional stability) Residence Time Long residence times are not advised 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

Low and stable εr • Ultra-low loss • Low water absorption • Hydrolysis resistant • Excellent impact strength • Mass production friendly APPLICATION BULLETIN A PREPERM radome grade gives you a longer and wider scanning range compared to common resins. 40 m Comparison of PREPERM radome grade and common resin at 24 GHz and 79 GHz bands Common Resin Common Resin PREPERM™ RB260 PREPERM™ RB260 PARAMETER PBT+GF PEI PREPERM RADOME GRADE ELECTRICAL εr @ 77 GHz 3.5–4.2 3.1 2.6 Tan @ 77 GHz 0.03 0.003 0.003 Isotropic @ 77 GHz No Yes Yes MECHANICAL Impact strength -20°C/+23°C notched izod 6kJ/m2/6kJ/m2 6kJ/m2/6kJ/m2 25kJ/m2/35kJ/m2 Elongation @ break 3% 40% 22% Brittleness Yes Yes No THERMAL Max use temp (HDT) 200–220°C 190–200°C 150–180°C Inherent flammability HB V0 V1 to V0 ENVIRONMENTAL Water absorption 0.4% 1.25% 0.2% Chemical resistance Good Excellent Good Hydrolysis resistant Specific Grade Yes Yes MANUFACTURING Batch-to-batch consistency Limited Excellent Excellent Moldability Excellent Good Good Abrasive Yes No No Mold shrinkage Inconsistent, warpage issue Homogenous Homogenous Raw material price Low High Moderate Copyright © 2022, Avient Corporation.

PRODUCT BULLETIN PROPERTY COMPARISON TRILLIANT HC VS NYLON Flexural Tensile — PKE-GF PA12-GF PA612-GF Shrink Modulus Chemical Resistance Flexural Tensile (Dry)Tensile CO2 Emission Factor — Trilliant HC — PA6-GF — PA66-GF Wear 1: Poor 3: Good 5: Excellent Flexural Tensile — PKE-GF PA12-GF PA612-GF Shrink Modulus Chemical Resistance Flexural Tensile (Dry)Tensile CO2 Emission Factor — Trilliant HC — PA6-GF — PA66-GF Wear 1: Poor 3: Good 5: Excellent 1.844.4AVIENT www.avient.com Copyright © 2023, Avient Corporation.

EXTRUDER Screw 3/4" to 6" Polyethylene type—Single flight, no mixing section, 1.5–2:1 compression ratio Tooling Semi-Pressure type: 30°–40° angle Die On size with 1/8" or less land L/D 24:1 recommended Screen Pack No screen pack (Optional depending on pressure) Cooling Trough 120–150°F (50–65°C) recommended Feeder Gravimetric type preferred—3 compartment for cross-linked Dryer Desiccant type, 4 hours at 160°F (70°C) For ECCOH™ compound only; never put Dry Silane in Dryers PROCESSING Temperature ECCOH 5000 Series ECCOH 6000 Series Wire Preheat 180–250°F (80–120°C) 180–250°F (80–120°C) Feed Zones 200°F (93°C) 275°F (135°C) Transition 275°F (135°C) 325°F (163°C) Metering 300°F (150°C) 375°F (190°C) Head/Die 330°F (165°C) 420°F (215°C) Target Melt 330–340°F (165–170°C) 420–440°F (215–225°C) Flame at Die Tip Yes—as needed Line Speed Shear sensitive: Observe Melt Temperature, Motor Amperage, and Pressure Purge Compound HDPE Copyright © 2020, Avient Corporation.

© 2020, All Rights Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012 THE CHALLENGE Regarded as an innovative startup in the stand up paddle industry, Carbonerro™ has continued to push boundaries with products that redefine a new standard of quality, performance and excellence for SUP (stand up paddleboard) enthusiasts.

MATERIAL REDUCES COSTS WITH LOWER SPECIFIC GRAVITY, AND HIGHER FLOW THAN COMPETITIVE TPV © 2021, All Rights Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012 To learn more about Versalloy™ Thermoplastic Vulcanizate, contact Avient at +1.844.4AVIENT (1.844.428.4368) or visit avient.com.

HITTING THE SWEET SPOT FOR ARCHERY ENTHUSIASTS SPECIALTY MATERIALS AND UPGRADED DESIGN ACHIEVE GAME-CHANGING PRECISION © 2022, All Rights Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012 Interested in learning more about specialty TPEs or advancing your design?

© 2021, All Rights Reserved Avient Corporation, 33587 Walker Road, Avon Lake, Ohio USA 44012 To learn more about Versaflex™ TPEs, contact Avient at +1.844.4AVIENT (1.844.428.4368) or visit avient.com THE CHALLENGE A leading North American medical contract manufacturer faced a challenge when molding the gasket for a contact lens container.