OnFlex LO - HVAC Flap - Spanish PROVEEDOR TIER 2 R E J I L L A P A R A S I S T E M A S D E V E N T I L A C I Ó N Y C A L E F A C C I Ó N • Eliminar el post-calentamiento de las piezas a fin de lograr el nivel de olor necesario (≤3.0 VDA 270) • Tener la menor emisión de compuestos orgánicos volátiles (VOC/FOG) (VDA 278), con el mismo compresión set del material anterior • Menos pasos de procesamiento y menores costos de energía para el moldeador • Se lograron los niveles VOC/FOG requeridos y se cumplió el desempeño con el estándar de compresión set OnFlex™ LO REQUERIMIENTOS CLAVE ¿POR QUÉ AVIENT?

Such advice, for example how to set up blow molding machines, is not equipment specific and therefore ColorMatrix would always recommend using local or expert technicians in addition to following best practice points listed below; • Preforms should be conditioned for minimum 24 hours prior to blowing • Preforms should always be used in a FIFO manner (First In, First Out) • Octabins of preforms should be segregated and blown per resin type, i.e. not mixed with other resins • A preform traceability system should be in place such that any process upsets can be quickly followed up and corrected • Enhanced QC preform checking resources for bottle distribution, aesthetics and integrity should be on-hand during the performance optimization trials • Prior to any process optimization, the blowing machine performance should be verified as being within normal i.e. accepted standard ranges and all important components and control features are working satisfactorily. Maximum speed output should be attainable prior to any ‘recipe’ setting trials Copyright © 2020, Avient Corporation. CAUSE AND EFFECT DIAGRAM Methods Machines Materials Manpower energy saving during SBM Maintenance instructions Operating instructions Operator Job spec NIR Lamps SBM Type/Design vPET reheat content vPET formulation rPET blend/quality Temperature recording Temperature measurement probe External temperature Inappropriate Manual Training New Alignment Same Throughput Too many tasks Time conflict Age/intensity variable Set up conditions Configuration - When starting to process a new resin, first run through new preforms for 15 minutes at ‘standard’ conditions to establish steady state conditions prior to any process optimization - Slowly start to reduce preform blowing temperatures until failures are present (visible pearl internal wall or pearl feet) - Increase blowing temperatures until defects are eliminated - QC check bottle quality for acceptance versus established tolerances - Change the power consumption profile in the ovens for early heat and longer sink times but ensure overall temperatures do not exceed cold crystallization temperature - Repeat temperature reduction stage and then defect elimination stage to test if further optimization is possible - Recheck QC bottle quality for acceptance versus established tolerances - Log all process parameters and create new specific ‘recipe’ for future use

Setting and periodically reviewing environmental objectives and targets assures excellence in environmental leadership. Avient strives to be the industry leader in safety and health by setting aggressive goals, measuring performance, and making necessary adjustments.  Setting goals and objectives that drive continual improvement and check effectiveness of risk reduction measures in product safety and stewardship

The substance is used in powdered form in industrial settings only. EXPOSURE HUMAN HEALTH SAFETY ASSESSMENT Human Health The substance is used in industrial settings only. Uses in industrial settings are generally under controlledconditions and often in closed system.

Setting and periodically reviewing environmental objectives and targets assures excellence in environmental leadership. Avient will be the leader in safety and health by setting aggressive goals, measuring performance, and making adjustments when necessary.  Setting goals and objectives that drive continual improvement and check effectiveness of risk reduction measures in product safety and stewardship

With a custom view you can create a set of advanced search filters. 1. You can use the following settings when creating or editing a custom view for a CSP table. 4. Once complete, save your settings.

IATF Certificate Place and date: For the issuing office: Katy, TX, 22 May 2025 Revision 10 DNV - Business Assurance 1400 Ravello Drive, Katy, TX, 77449- 5164, USA Sherif Mekkawy Management Representative Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid. ACCREDITED UNIT: DNV Business Assurance USA Inc., 1400 Ravello Drive, Katy, TX, 77449-5164, USA - TEL: +1 281-396-1000. www.dnv.com Page 1 of 2 MANAGEMENT SYSTEM CERTIFICATE Certificate no.: 11229-2006-CHN-IATF IATF Certificate No: 0573810 Valid: 21 May 2025 – 20 May 2028 This is to certify that the management system of PolyOne - Suzhou, China EM Sector, 77 Shenggang Street, Suzhou Industrial Park, Suzhou, Jiangsu, China 215024 (USI: CF4943) and, if applicable, the remote supporting locations as mentioned in the Appendix accompanying this Certificate has been found to conform to the Quality Management System standard: IATF 16949:2016 This certificate is valid for the following scope: DESIGN AND MANUFACTURE OF PLASTIC COMPOUNDING MATERIAL EXCLUSION: NONE http://www.dnv.com Certificate no.: 11229-2006-CHN-IATF IATF Certificate No: 0573810 Place and date: Katy, TX, 22 May 2025 Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid.

China TEL: +86 21 32799000 Zhu Hai Ming Management Representative Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid. Park, Pudong, Shanghai, China, 201203 and the sites as mentioned in the appendix accompanying this certificate has been found to conform to the Quality Management System standard: ISO 9001:2015/GB/T 19001-2016 This certificate is valid for the following scope: Design and Manufacture of Masterbatch C ertificate No: 7071-1998-AQ-RGC-RvA P lace and date: Shanghai, 30 March, 2018 Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid.

IATF Certificate Place and date: For the issuing office: Katy, TX, 10 December 2024 Revision 2 DNV - Business Assurance 1400 Ravello Drive, Katy, TX, 77449- 5164, USA Sherif Mekkawy Management Representative Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid. No. 1, Qihang Industry Park, Haoxiang Road, Shajing Town, Baoan, Shenzhen, Guangdong, China 518104 (USI: C5M65R) and, if applicable, the remote supporting locations as mentioned in the Appendix accompanying this Certificate has been found to conform to the Quality Management System standard: IATF 16949:2016 This certificate is valid for the following scope: DESIGN AND MANUFACTURE OF PLASTIC COMPOUNDING MATERIAL EXCLUSION: NONE http://www.dnv.com Certificate no.: 273138-2018-AQ-RGC-IATF IATF Certificate No: 0558323 Place and date: Katy, TX, 10 December 2024 Lack of fulfilment of conditions as set out in the Certification Agreement may render this Certificate invalid.

STANDING APART FROM THE COMPETITION HOW DO MY CMF CHOICES SET ME APART FROM COMPETITORS? Finding a color, material and finish that catches the eye and sets you apart from your competition is vital. D E S I G N I L LU M I N AT E S VISUALIZING COLOR, MATERIAL & FINISH SELECTION WE’VE DEVELOPED A TOOL THAT ALLOWS YOU TO SET THE CRITICAL FACTORS FOR YOUR PROJECT, ALLOWING YOU TO MAKE INTELLIGENT CMF DECISIONS AND ACCELERATE DEVELOPMENT.