Energy: o Diesel Fuel Consumption: 2,868,323 kWh o Natural Gas Fuel Consumption: 178,696,287 kWh o Renewable Energy Consumed - Self Generated (solar): 681,059 kWh o Renewable Energy Consumed - Self Generated (Wind): 2,385,048 kWh o Grid Electricity Consumed: 409,650,679 kWh o Renewable Energy Credits (REC) Purchased: 112,413,420 kWh o Renewable Electricity Consumed – Offsite: 138,415,253 kWh Page 2 Period covered by GHG emissions verification: • January 1, 2023 to December 31, 2023 Global Warming Potential (GWP) and emission factor data sets: • IPCC GWP: AR6 • USEPA Emission Factor Hub, released 2024 • USEPA eGRID, released 2024 • Final Rule (40 CFR 98) - Industrial Sector 2013 • DEFRA, released 2023 • IEA, released 2023 • European Residual Mix, released 2022 v2.0 GHG Reporting Protocols against which verification was conducted: • World Resources Institute (WRI)/World Business Council for Sustainable Development (WBCSD) Greenhouse Gas Protocol, Corporate Accounting and Reporting Standard, Revised Edition (Scope 1 and 2) and the GHG Protocol Scope 2 Guidance, an amendment to the GHG Protocol Corporate Standard • WRI/WBCSD Corporate Value Chain (Scope 3) Accounting and Reporting Standard Verification Protocols used to conduct the verification: • ISO 14064-3 Second Edition 2019-04: Greenhouse gases - Part 3: Specification with guidance for the verification and validation of greenhouse gas statements • Apex’s standard procedures and guidelines for external Assurance of Sustainability Reports and International Standard on Assurance Engagements (ISAE) 3000 Revised, Assurance Engagements Other than Audits or Reviews of Historical Financial Information (effective for assurance reports dated on or after Dec. 15, 2015), issued by the International Auditing and Assurance Standards Board.

This includes measuring performance and setting appropriate goals to promote continuous improvement

Certificate Avient Corporation This is to certify that the Responsible Care Management System of: Avon Lake Corporate 33587 Walker Road Avon Lake OH 44012 United States (WITH ADDITIONAL FACILITIES LISTED ON ATTACHED ANNEX) has been assessed by ABS Quality Evaluations, Inc. and found to be in conformance with the requirements set forth by: The Responsible Care Management System is applicable to: CORPORATE SUPPORT ACTIVITIES, DESIGN, MANUFACTURE AND DISTRIBUTION OF COLOUR AND ADDITIVE CONCENTRATES, THERMOPLASTIC RESINS AND PELLETS, SPECIALTY COMPOUNDS AND COLORANTS.

Certificate Avient Corporation S E s Certificate Of Conformance This is to certify that the Quality Management System of: Avient Corporation 33587 Walker Road, Building 428 Avon Lake OH 44012 United States has been assessed by ABS Quality Evaluations, Inc. and found to be in conformance with the requirements set forth by: ISO 9001:2015 The Quality Management System is applicable to: Manufacture of plastic compounds, color and performance additives, engineered thermoplastics, vinyl resins, custom mixed plastic materials, custom and commodity colorants for plastics, polyurethane systems, and plasticizers with design and sampling support at Suwanee, GA, and purchasing, customer service, logistics, quality, design and sampling support at PolyOne Corporate Headquarters at Avon Lake, OH, and distribution of resins Certificate No: 31307 Certification Date: 12 OCT 1995 Effective Date: 11 JUL 2024 Expiration Date 07 OCT 2025 Revision Date: 17 JUL 2024 Dominic Townsend, President Page 1 of 4 S E s ISO 9001:2015 Certificate Of Conformance ANNEX Certificate No.: 31307 Avient Corporation At the below facilities The Manufacture of Pultruded and Filament wound components Pultrusion and CRTM 3943, Valley East Industrial Drive, Buildings 1,2,3,4 Birmingham - AL 35217 United The Manufacture of Pultruded and Filament wound components Pultrusion and Filament Wound Tubing 3968, Valley East Industrial Drive, Building 5 Birmingham - AL 35217 United States The Manufacture of Pultruded and Filament wound components Pultrusion 3950, Valley East Industrial Drive, Building 6 Birmingham - AL 3517 United States Corporation Management of QMS.

Vents should be placed at the intersection of each 90° bend in the runner system off of the cold slug well and vented to atmosphere Black Specks Contamination • Purge barrel with general purpose PP • Verify correct nozzle is being used • Pull screw for cleaning Degraded/overheated material • Decrease melt temperature • Decrease injection speed • Use appropriately sized barrel Brittleness Degraded/overheated material • Decrease melt temperature • Decrease injection speed • Use appropriately sized barrel Gate location and/or size • Relocate gate to nonstress area • Increase gate size to allow higher flow rate and lower molded-in stress Burning Process related Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Fibers/Minerals on Surface or Uneven Surface Appearance Melt temperature too low • Increase injection speed Insufficient packing • Increase hold pressure and time Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Decrease pack pressure • Decrease shot size Melt and/or mold too hot • Decrease screw speed Loose clamp • Reset mold height • Increase clamp tonnage Troubleshooting Recommendations Incomplete Fill Melt and/or mold too cold • Increase nozzle and barrel temperatures Mold design • Enlarge or widen vents and increase number of vents • Check that vents are unplugged • Check that gates are unplugged • Enlarge gates and/or runners • Perform short shots to determine fill pattern and verify proper vent location • Increase wall thickness to move gas trap to parting line Shot size • Adjust transfer position to 98% full Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Increase screw decompression Shrink Too much shrink • Increase cooling time Too little shrink • Decrease cooling time Sink Marks Part geometry too thick • Reduce wall thickness • Reduce rib thickness Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase packing pressure Troubleshooting Recommendations (continued) Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Decrease cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Part is too hot • Increase cooling time Warp Process related • Increase cooling time • Increase pack pressure • Increase pack time Mold design • Inspect for non-uniform mold cooling Part design • Inspect for non-uniform wall thickness Temperature control unit incorrect temperature • Check settings • Inspect thermocouple Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Perform short shots to determine fill pattern and verify proper vent location • Add vents and/or false ejector pin • Move gate location 1.844.4AVIENT www.avient.com Copyright © 2022, Avient Corporation.

WITH ADDITIONAL FACILITIES LISTED ON ATTACHED ANNEX) has been assessed by ABS Quality Evaluations, Inc. and found to be in conformance with the requirements set forth by: Page 2 of 10 Facility: Avient Corporation - Albany 4 Rothwell Ave, PO Box 300-009 Albany Industrial Estate Auckland 0632 New Zealand Facility: Avient Corporation - Avon Lake (SEM) 554 Moore Road Activity: Design and Manufacture of Colorants and Additives for Plastics Activity: Design and Manufacture of Specialty Engineered Thermoplastics Facility: Avient Corporation - Barbastro Pol.

WITH ADDITIONAL FACILITIES LISTED ON ATTACHED ANNEX) has been assessed by ABS Quality Evaluations, Inc. and found to be in conformance with the requirements set forth by: Page 2 of 10 Facility: Avient Corporation - Albany 4 Rothwell Ave, PO Box 300-009 Albany Industrial Estate Auckland 0632 New Zealand Facility: Avient Corporation - Avon Lake (SEM) 554 Moore Road Activity: Design and Manufacture of Colorants and Additives for Plastics Activity: Design and Manufacture of Specialty Engineered Thermoplastics Facility: Avient Corporation - Barbastro Pol.

ECCOH™ Specialty Solutions Helping Cable Manufacturers Meet CPR Standards PRODUCT BULLETIN ECCOH™ Low Smoke and Fume Non-Halogen (LSFOH) formulations offer a range of non- halogen, flame retardant solutions that enable manufacturers to meet the Construction Products Regulation (CPR) standards set out by the harmonized European Standard, EN13501.

Check settings 2.

ECCOH™ Specialty Solutions Helping Cable Manufacturers Meet CPR Standards PRODUCT BULLETIN ECCOH™ Low Smoke and Fume Non-Halogen (LSFOH) formulations offer a range of non- halogen, flame retardant solutions that enable manufacturers to meet the Construction Products Regulation (CPR) standards set out by the harmonized European Standard, EN13501.