Using a specific masterbatch enables proper charging. Together with the fiber denier, gram weight, and number of layers, this masterbatch ensures the middle layer of the filter can effectively trap smaller particles.

Color and Additive Masterbatches for the Electrical and Electronics Industry UL94 compliant masterbatches and flame retardant solutions meet the latest UL94 and Glow Wire standards

CLEVELAND – October 31, 2017 – PolyOne today launched OnColor™ Brilliant Metallic Colorants, a striking new line of special effect masterbatches that finally meet the need for paint replacement and premium surface finish. Our customers across multiple industries have been looking for a paint-free solution with no tradeoffs, which drove us to develop this new masterbatch.

Lowered energy requirements versus painting and the reduction of VOCs also made this masterbatch a more environmentally sustainable solution.

HDPE is not recommended for purging as it can cause delamination or lead to black specks. Sink Marks Melt too hot • Decrease nozzle and barrel temperatures Insufficient material volume • Increase shot size • Increase packing pressure Part geometry too thick • Reduce wall thickness • Reduce rib thickness Processing Guide 5 Flash Injection pressure too high • Decrease injection pressure • Increase clamp pressure • Increase transfer position Excess material volume • Adjust transfer position • Decrease pack pressure • Decrease shot size Melt or mold too hot • Decrease nozzle and barrel temperatures • Decrease mold temperature Loose clamp • Reset mold height • Increase clamp tonnage Shrink Too much shrink • Increase cooling time Too little shrink • Decrease cooling time Burning • Reduce decompression Mold design • Clean, widen and increase number of vents • Increase gate size to reduce shear Wet material • Verify material is dried at proper condition Nozzle Drool Nozzle temperature too hot • Decrease nozzle temperature • Decrease back pressure • Increase screw decompression • Verify material has been dried at proper conditions Incorrect nozzle • Use reverse taper tip Weld Lines Melt front temperatures are too low • Increase pack and hold pressure Mold design • Increase gate size • Identify end of fill pattern and verify proper vent location • Add vents or increase vent width • Move gate location 6 Artisan Pre-Colored Thermoplastics Warp • Increase melt temp • Reduce injection speed • Increase pack pressure • Increase pack time • Decrease mold temperature • Increase cool time Mold design • Non-uniform mold cooling Part design • Non-uniform wall thickness Thermolator incorrect temperature • Check settings • Inspect thermocouple Sticking in Mold Overfilled cavity • Decrease injection rate and pressure • Decrease hold pressure • Decrease cooling time Part too hot • Decrease barrel temperature • Decrease mold temperature • Increase cooling time Mold design • Increase draft angle • Polish cores in direction of ejection Black Specks Contamination • Purge machine Degradation • Reduce melt temperature • Reduce screw speed • Reduce back pressure Machine related • Check for wear on screw, barrel or check ring Delamination • Increase melt temperature • Decrease injection speed • Purge barrel to eliminate material contamination Mold design • Reduce sharp corners in material flow path • Increase venting Processing Guide 7 Discoloration Oversheared material • Decrease melt temperature • Decrease injection speed • Reduce residence time Mold design • Increase gate sizing Dry material • Check moisture of material to ensure it is within the recommended moisture percentage for molding 1.844.4AVIENT www.avient.com Copyright © 2020, Avient Corporation.

% Specific Color Heat BROWN 83MB01 (c) Iron Oxide, Tan HR 60 1.78 PBr-11 1 I/O SBR 83MB02 (c) Iron Oxide, Light 68 2.1 PBr-6 2 C I/O SBR 83MB03 (c) Iron Oxide, Dark 60 1.83 PBr-6 2 C I/O SBR 83EP02 Iron Oxide, Light 69 1.98 PBr-6 2 C I/O EPDM 83EP03 Iron Oxide, Dark 69 1.98 PBr-6 2 C I/O EPDM BLACK 90MB01 (c) Furnace N-330 31 1.2 PBk-7 1 I/O SBR 90MB05 (c) Iron Oxide 60 1.8 PBk-11 2 C I/O SBR 90EP01 Furnace Black 33 1.05 PBk-7 1 I/O EPDM 90EP05 Iron Oxide 55 1.56 PBk-11 2 C I/O EPDM ALUMINUM 61MB01 Aluminum 70 1.5 PM-1 1 I/O SBR 61EP01 Aluminum 60 1.31 PM-1 1 I/O EPDM RS = Red Shade YS = Yellow Shade VYS = Very Yellow Shade BS = Blue Shade VBS = Very Blue Shade GS = Green Shade NC = Non-Crystallizing HR = Heat-Resistant (a) = Potential Migration at Low Use Levels (b) = Poor Alkali Resistance - Not Recommended for Open Steam Cure (c) = Six Month Shelf Life LIGHTFASTNESS I = Indoor Only I/O = Indoor or Outdoor Mass = Outdoor Masstone Application Only C = Some Caution Advised HEAT STABILITY 1 = Above 400°F 2 = 350°F–400°F 3 = Below 350°F C = Some Caution Advised 1.844.4AVIENT www.avient.com Copyright © 2024, Avient Corporation.

https://www.avient.com/products/polymer-colorants/solid-color-masterbatches/oncolor-sc-super-concentrate-technologies

BUILDING MATERIALS RETAILER R O O F I N G M E M B R A N E S • Improve marketing claims for product performance and polymer integrity • Prevent and improve field life, and protect product from the growth and appearance of flora, fungi and algae from outdoor environmental exposures • Ability to convert materials from liquid to solid in order to accommodate advanced manufacturing technique • Seeking OBPA alternative • Delivered a product differentiating solution that eliminated both polymer-degrading microbials and mitigated the flora and fungal accumulation that causes discoloration and staining • Enabled versatility with combined liquid and solid masterbatch solutions • Provided a cost-effective and environmentally friendly OBPA alternative WithStand™ Antimicrobial Additives KEY REQUIREMENTS WHY AVIENT?

https://www.avient.com/products/polymer-colorants/solid-color-masterbatches

Certificate Number: Certificate expiration date: Effective date: 31-10-2022 30-10-2025 Expiry date of previous cycle: 30-10-2022 31-10-2016 ES133794 Scope of certification: MANUFACTURING OF MASTERBATCHES, ADDITIVES AND COMPOUNDS FOR PIGMENTING THERMOPLASTIC MATERIALS USED IN FOOD INDUSTRY ISO 22000:2018 POLIGONO INDUSTRIAL EZCABARTE, C/H, Nº3 - 31194 - ORICAIN - NAVARRA - ESPAÑA AVIENT ESPAÑA, S.L.